Clear Plastic
Apr 27
2006
2006
Tips for Machined Plastic Component Design
The following are guidelines for good machined plastic component design. These are not hard rules but suggestions to maintain reasonable pricing. Exceeding the guidelines will usually result in higher effort and cost for the component.
Each part configuration and application is unique. For specific design support, contact Connecticut Plastics’ engineering at 203-265-3299 or on the web at Connecticut Plastics.com
- Flatness: From the extrusion and cooling, plastics have stress gradients through their cross section which are not relieved by post processing at the manufacturer. Plastic’s flatness stability is substantially lower than metals. Consider the following to improve.
- Balanced design. Dish shaped plastic machined components are notoriously difficult to avoid warpage.
- .003″ per a 4″ square, unrestrained, is typical. Tighter tolerances require better fixturing and more machining.
- Consider specifying parallelism instead of flatness. If the plastic part is attached to another (especially a metal part), unrestrained flatness is unimportant. The plastic part will follow the contour.
- Consider restrained flatness. Again if attached to another component, the plastic part will conform to the contour.
- Pick a stable material: Low performance materials will easily warp. For tight flatness requirements, harder plastics are better. Try Ultem, PPS, Peek and Acrylic
- Hire a plastic machining company. Flatness can change over time while sitting on a shelf in the stock room. Advanced processing really works for flat critical components.
- Threaded Inserts: For single time assembly, threaded inserts are not necessary given proper torque levels are utilized. Inserts do not add appreciable additional holding power. Applications requiring repeated disassembly (usually for cleaning) do benefit to avoid thread stretch. Heat staked inserts are a better solution than Helicoils by giving higher pullout power. Helicoils impart high stress levels into a threaded hole resulting in crazing at the thread root in sensitive materials. Helicoils are acceptable in materials that do not heat stake well and have good toughness like UHMW.
- Polishing: Typically applies to clear plastics like Acrylic, Polycarbonate, Polysulfone and Ultem but is important for finish improvement in opaque materials as well. Polishing methods are direct machine polish, vapor polishing, flame polishing, and buffing. The most professional looking finishes are accomplished by machining and polishing with one vendor. Polishing only services are available but the finish usually is not as good. Heavy polishing can never make up for and overcome poor machining. Melted surfaces in the machining process will invariably result in stress cracking after polishing.
- Finishes: There is continual demand for better finishes to improve product performance. Given the capabilities of modern CNC equipment, do not accept surface finishes above 63 micro inches from a machining vendor.
- A 32 to 40 micro inch is consider a standard machined plastic finish for a +/- .005 toleranced component and should not incur any additional cost to produce.
- Finishes below 32 are reasonable and to be expected on close tolerance parts (+/- .0005).
- Finishes between 10-20 micro inches are typical for a polished plastic component especially as a turned component.
- Inside milled pocket finishes always have higher/worse finishes. The action of the nose of the endmill does not facilitate clean cutting and chip removal.
- Exterior flat milled areas can have a very good surface finish
- In 3D profile milling a good finish requires a large number of passes from a ball endmill. Carefully specify the maximum allowable finish to avoid excessive machine time.
- Finishes below 10 are difficult to achieve and may require lapping or similar with limited application to part geometry.
- Some plastics like Teflon cannot have a surface finish below 20 via any method because of the porosity of the material.
- Tolerances: Dimensional tolerance holding is very much configuration and material dependant. However some general rules do apply. +/- .005″ is an easy to reach tolerance for all but very large dimensions in unstable material. For parts with a volume of 1″ cubed and below, +/- .003 is readily held. For small components, even in soft materials like Teflon, +/- .001 is reasonable. +/- .0005″ and +/- .0002″ are manufacturable with small dimensions in stable materials. The corresponding surface finish must be improved as tolerances are tightened to avoid measurement repeatability errors.
- Material Selection: There are many good references for plastic material selection by the major manufacturers of both resin and stock shapes. Select the material carefully, as plastics are capable of long term change. Field failures do occur when a plastic component reacts with a chemical in service long after the part has been approved for use by inspection. Be aware that plastic choices are not limited to unfilled materials only. Fillers such as glass fiber can enhance particular characteristics.
- Dimensional Stability: Like flatness above, machined plastics do not have near the same stability as an identical metal component. Plastic components are affected over the long term by many factors
- Thermal change: Plastics’ CTFE is higher than most metals. Some plastics have a measurable change simply though contact with body heat.
- Moisture absorption: Nylon can soak up to 9% of its weight at saturation having a dramatic affect on dimensional change. Try Noryl for hot water applications.
- Creep: Materials like Teflon and UHMW when placed under high pressure will change shape and extrude from a joint.
- Off-gassing: Many machined plastics off gas as a reaction to the extrusion and machining process. Notably, Delrin components shrink over time from the effect.
- Stress relaxation: Both the extrusion and machining process impart stress into a machined plastic component. Post processing can help, however part configuration determines which direction the plastic will relax and change size.
- UV/aging: Plastics age and embrittle especially from exposure to UV or chemicals.
For more information, please check out the Plastic Part Design Guide on our website. Or learn about the history of plastics, and it’s chemical properties at our On Line Learning Center. A great reference for information on plastics, engineering and chemistry.
About the Author
Tom Rohlfs, Engineer and President
1264 Old Colony Road
Wallingford CT 06492
Applying Future to Clear Plastic Parts
|
|
Wilton 570-1121 Easy Flex 3-Piece Silicone Spatula Set, Blue $5.91 Silicone Baking Accessories. Silicone is the Wonder Kitchen Tool: it can be used in the oven (up to 500F/260C), toaster over, microwave, refrigerator and freezer and it is virtually unbreakable. These silicone utensils are the perfect tool cold foods: Jell-O, ice sculptures, Candies and hot foods: cake, muffins, bread, pies, main and side dishes and so much more! The flexibility makes removing foo… |
|
|
OXO Salad Spinner … |
|
|
Pyrex 6022369 Storage 14-Piece Round Set, Clear with Blue Lids $19.99 Pyrex 14-pc Storage Set ***OPEN BOX*** This NEW product you are browsing has been inspected by our certified technicians to ensure that it meets factory specifications; it is guaranteed to be in perfect working order.The Equipment is sold in AS IS condition and returns will not be accepted so please contact us with any questions BEFORE placing an order at 1-800-572-3224 Ext: 243. We ac… |
|
|
WAND MINI BLIND 24CLEAR [Misc.] $4.22 - Color: Faded Clear – Comes with installation Instructions – We don’t have anything 48 Inches or longer – Slide plastic collar up the tilter shaft – Place hole at top of wand onto the hook of the tilter shaft – Diameter: 1/4 Inc – Shape: Hexagon – Slide plastic collar down tilter shaft to cover hook – 29 Inches long… |
|
|
OfficeMax 25-Pack Standard CD Jewel Cases 0M96045 $9.99 Need to replace your cracked or missing jewel cases? Let OfficeMax help. Type: Case. Compatible Media Type: CD / DVD. Replace cracked or missing standard-size jewel cases. Durable, high-impact plastic construction. Each case holds 1 disk. Clear front w/ black insert. Protect your CDs and DVDs with high impact plastic… |
|
|
PASSPORT PROTECTOR $1.50 PASSPORT PROTECTOR… |
|
|
AR Blue Clean AR383 1,900 PSI 1.5 GPM 14 Amp Electric Pressure Washer with Hose Reel $153.72 This AR Blue Clean Electric Pressure Washer gives you the power and convenience you need with a built-in hose reel and accessory storage that keep essentials organized and easy to access. Pressure (PSI): 1,900, Flow (GPM): 1.6, Motor: Universal, HP: 1.5, Volts: 110, Amps: 12, Pump: Axial radial, Drive: Direct, Gun: AR easy trigger auto stop, Nozzle Type: Variable angle spray, Orifice Size: 1.10, H… |
|
|
Hobart 770096 Welding Oxy-Acetylene Goggle – 50mm Eye Cup $8.99 Fixed front – rigid 50 mm dual cup eye goggles come with #5 shade for acetylene welding. Compact design with elastic headband provides years of trouble-free eye protection.Ideal for use with welding applicationsRigid 50 mm dual cup for optimal eye protectionElastic headband helps the goggles stay in place for lasting protectionNumber-5 shade shields against brightnessCompact design for easy, durab… |
|
|
500 CLEAR Reclosable Zipper Bag. 2” x 3” – 2 mil thick $1.65 500 New Resealable Plastic Bags . These high quality reclosable plastic bags allow you to have the bags you use most on hand. The reclosable seals open all the way to the edges of the bags giving you full use of the interior. Each has a 2 mil thickness and measures approximately 2″ x 3″… |
|
|
The Bellero Shield $1.99 … |
Comment